Monday, February 26, 2018

Youtube daily report w Feb 26 2018

Again this tremor in hands, tremor in voice and certain uncertainty

Certain uncertainty...I can say like that.

Everytime when you do a presentation of a new device of your own, you are always uncertain how people will perceive it

What will reviewers say about it and what kind of opinion eventually will people have

I'm always very worried at such moments, that is why i will gladly read your comments below this video

So folks, let's not delay this exciting moment and let's roll. Intro...

Hello everyone! Alex from VapersMD is here

And i'm glad to welcome you on my channel

And today i will tell you about my new RDA, that i made in cooperation with Vandy Vape

Friends, this is this is a continuation of the line of Berserker MTL

This is Berserker MTL RDA

Single coil RDA with familiar posts, very deep juice well, with hot swap of airflow tubes feature, airflow adjustment options, top fill and also this RDA can easily work with squonk mods

it was made to be quite compact - only 18mm in diameter, but there were own reasons for it

Initially this RDA had 3 variants, and all of them was 22mm in diameter

They had different airflow adjustment, possibilities of change the airflow and other good features and options which i can't show you right now, since it's possible that we will use them in our other devices

In one RDA i didn't like the adjustment, in second RDA i didn't like the swap of the airflow tubes and in third i didn't like the noise this RDA produced

But one of the main cons, that all three of these devices has - it is minimal amount of flavor

So in the end there was made a decision to change the diameter of this RDA down to 18mm to reduce the chamber, to get correct flavor with MTL draw

And you know, in my opinion we are succeeded

Friends, i will not be delaying the moment of close up to show you massive kit and tell you how to launch this RDA

Let's dive down

Okay friends, let's get to the unboxing. I won't be focusing on the package since it's standard

And all of the kit contents we have on the desk

So in the kit we have an RDA itself

24mm decorative ring

22mm decorative ring

Coil correction tool for more convenient coil installation

That famous blue screwdriver. It must be here.

Allen key for squonk pin installation

Screw for negative post *note on the top - this is a screw for negative post*

Two spare post screws

Delrin top for drip tip since the drip tip is composite

Spare o-rings

Swappable airflow tubes

Pre-made coil, QC pass and User Manual

And now let's talk about specs. This RDA is made of stainless steel and available in 4 colors - steel, black, gold and rainbow

It have a slot for 510 drip tips, top cap for convenient refill, familiar posts for single coil installation, 6 swappable airflow tubes that is made of heatproof plastic with different holes and diameters

You can swap them when you have coil and cotton installed

Also airflow can be adjusted by turning the barrel

Juice well is 12.8mm deep

Main diameter of RDA is 18mm, but in the kit we have 2 decorative rings - 22 and 24mm

And now it's time for a detailed look and as always we start from the top

On the top we have 510 with heat sink, also this drip tip is composite and we have ultem cap

Top part is removable and its unscrews counter clockwise

You can easily swap it do delrin cap that we have in the kit

As i said it's 510 drip tip, it have 2 o-rings and inside it's cone shaped, the bore diameter is 3mm

Next we see the top cap which is for top fill. It have a knurling for convenient removing

Removing is easy and in the same moment it holds good due to correctly selected o-ring

On the inside it's cone shaped, which should positively affect the flavor

And of course you can install any of your favorite 510 drip tips into that slot

Next we see a perforated barrel. In it we have airflow holes - about the same amount as Berserker RTA, but one more (it's 6 holes)

So, it's 0.8mm, 1mm, 1.2mm, 1.4mm, 1.6mm and 2mm

And by turning this barrel you can adjust the airflow

This barrel is holds on 2 o-rings which is on the deck

And now let's talk about the deck itself. In here you can see a familiar posts, that was in Berserker MTL RTA, both in 24 and 22mm versions, with special walls for convenient coil installation and phillips head screws

I think you noticed those 2 big holes that we have in the deck. In these holes you will be inserting your airflow tubes

The airflow tube is look like so. One side have a hole for getting the air and in center it have a hole for blowing the coil. On the opposite side it's just blank plastic

As i said before in the kit we have 6 of these tubes with various holes and diameters

Okay, the smallest hole is 1.2mm

Next hole is 1.4mm

Third hole is 1.6mm

And fourth hole is 2mm

Also there is 2 non-standard tubes - one with 3 holes 1mm each and a stripe 3*0.5mm

So yes, friends, in here you have a lot of options to adjust the airflow and you can experiment as much as you want

Okay, let's see how the airflow tube is being inserted

Like i showed you there is two large through holes in the deck and you can insert this tube inside by a simple motion of the hand

Now it's Installed and centered and the tube sits in its groove

One side is blank and other side have a hole for getting the air

And now let's look how the deck look from the top. As you can see these holes are asymmetrical, it was made on purpose so it's be possible to fill the juice

Accordingly, when you have installed coil in here in the center will be the cotton. So you will be filling juice in both of these corners

Pay attention - this juice well is not divided, but it have slight deepenings for larger capacity

So when you fill it on one side, the juice will get to the other side

Also on the bottom we have sort of bridge, it is for spit-back protection while squonking. This is my sort of feature which i will be using almost in all of my RDA's

On the bottom it look like so. In here it's written Berserker MTL RDA, my logo, certificates, serial number and date of production and a line which says that manufacturer is Vandy Vape

Gold-plated screw that holds negative post and pin that holds positive post

This pin is adjustable. And in case it won't be long enough for you - you can unscrew it a bit

And if we continue unscrewing it, we will be able to install squonk pin

By unscrewing external pin we getting access to the main screw which holds positive post. We will also have to unscrew it

And after we will be able to install the squonk pin with allen key from the kit

In that simple way we are installing the squonk pin in this RDA

Okay friends, now we can use this RDA on squonk mods

This is good~

Moving forward, let's finish with a kit. In the kit we have 2 decorative rings - one is 24mm in diameter, other is 22mm in diameter

And it's pretty simple to use them - you will need one of them, depends on what diameter your mechanical mod or box mod is

Put that decorative ring on the bottom part of the RDA and after that screw the RDA on the box mod or mechanical mod

This is how it will look at box mods that is fit 22mm diameter atomizers

For understanding the size - at the left hand is Berserker 24mm and at the right hand is Berserker MTL RDA

Well, i think we saw enough so it's time to and launch it. Let's install the coil

The sequence of actions is important. Firstly - install the coil and glow it and after that you can insert the airflow tube

To prevent the plastic tubes from damaging by glowing coils

But friends, I can assure you - it's heatproof plastic and when you use the RDA as intended nothing's gonna happen to it

But when you glow the coil and temperature of it rise to the maximum - in that case even that heatproof plastic might not endure it

So again - install the coil, glow it and only after this insert the airflow tube

Okay folks, let's get to the coil installation. I will use the fused clapton coil from a kit

Also this wire can be purchased separately and it's named Superfine MTL Fused Clapton Wire

This wire is made by Vandy Vape, on the top it have parameters, so you can build a fused clapton like this by yourself

This wire is made of Nichrome

For a start let's unscrew the screws

Inner diameter of kit coil is 2.5mm, but i will add one more wrap

So in the end we got 6 visual wraps

And now is one of the important moments - we will install the coil the way that leads will be on top and the coil itself on the bottom

After that place the leads in those grooves and tighten it with screws

Now correct the coil and bend the leads into those notches on both sides

And cut it

Now let's glow it

After the glow is done we need the airflow tube

You know, i have 2 favorite airflow tubes that i like the most in terms of draw and flavor - the tube with the smallest hole and tube with oval-shaped hole

So i will be using a tube with oval-shaped hole

Let's insert it. As you can see on one side we have insulator - insert it from this side - that will be way more comfortable and it will sit more even

Some tubes inserts a little tighter, but by applying a little force you will succeed

And here you might need a Coil correction tool which is also included in the kit

That's written on the back of it: Coil correction tool

As you can see it's angled for convenient manipulation with the coil. On one side diameter is 3mm, on the other it's 2.5mm

After you've installed the coil, glowed it and inserted airflow tube you can lower the coil closer to the airflow to have like 1mm between them

Now i'm totally satisfied with the coil and it's time to put some cotton

I'm using standard Koh Gen Do cotton. I peeled off the upper layer and now it's ready

And now regarding the amount of cotton and how much we should left of it - i think that this will be enough

I'm eyeballing it, but to clarify - it's going down to like second o-ring

Friends, don't try to stuff a lot of cotton - otherwise you will not have a juice well. So a lot of cotton in this RDA is completely unnecessary

And now i'll do something for the first time, since i don't like doing it - i will thin the cotton and by doing so i will reduce its amount and size

I think that amount is enough. No more tortures on it

Now just put the cotton inside the juice well in standard way

Pay attention - on one side cotton is blocked all the holes, but we will shift it after saturation

Right now, when we saturate it, a little bit of juice can get into the airflow. I suggest you to insert the airflow tube in the latest moment. Well maybe after you've adjusted the position of your coil

So to prevent juice getting into the airflow we move the airflow tube to the side and now we can to fill it with no problems even in this barbaric way

Great. Now let's get back the airflow tube in place

And now just shift the cotton a bit to drip into the juice well with no problems

I can say, friends, this RDA holds up to 20 drops. I was experimenting and it's 20 or 21 drops with dry cotton

You can freely drip on either sides

Also this RDA is having sort of leak-proof system - it didn't leaked even once out of airflow, so you can fill it to the edge and it will not leak through the airflow

After this we will need the barrel. Match it with airflow hole

I selected the second hole, it have optimal draw for me

Keep in mind that airflow tube should sit flush with the deck, otherwise you'll be unable to put on the barrel

As you can see i did it from the first try. And i think it's time get back to face-time, vape it and speak a little bit

Final resistance is 0.78Ω, power is 13.5W - it will be enough

So thanks for your attention in close up, let's roll

It is what it is friends

It works and it's capable of giving proper MTL draw - both loose and tight draw

And for those of you who is going to ask what's this box mod - it's Series B powered by DNA75 from Jac Vapor

This mod is made in England, it might be said it's high-end, and later i will definitely make a review on it

But let's talk about RDA itself

I think this RDA come out quite universal. You can freely use it on box mods, also you can easily use it on squonk mods since it have BF pin

By the way, RDA with beauty ring that is 24mm diameter, is gonna look like so

Fit of this squonk mod is 24mm and i think it looks not bad

But we're moving forward. Also you can use this RDA on mechanical mods that is 22 and 24mm in diameter with no problems

It's looks so-so. Not for everybody, as the saying goes.

And of course you can use this RDA on Ego-style mods with diameter 18mm and 19mm

This Ego-style mod is made by Joyetech and this RDA works perfectly with it

So friends, that's how this RDA looks on different mods. But there is another moment that we tried to achieve

And that is hot swap of airflow tubes feature

in order for you to be able to swap the airflow tube even with installed coil and cotton inside and try this RDA with other type of draw or airflow

For that you just need to take off that barrel and it's no matter if you have beauty ring installed or not

Take the airflow tube from the kit and just insert it inside and replace the previous one

After that put on the barrel, match the hole of the airflow you need and vape

And you know, you get different experience with different airflow tubes - different draw and flavor is changing a bit

And here you have a field for experiments

Overall friends, i have many things that i could have told you, but there is one moment that i want to show you

It is how to refill this RDA if you don't use squonk mods

You just take off the top cap, and in that simple way you drip the juice inside. This RDA accommodates up to 20 drops

Total capacity of juice well with no cotton inside is 1.2ml of e-liquid

And after you done dripping, put the top cap back and continue to vape

That's how we roll, friends

Okay, we're going to finalize this review

I want to say big thanks to Vandy Vape

I really like working with this company. They are great, they are the top

They do everything like a Tsar and it's a pleasure to have a business with them

To you friends - big thanks for your attention

Don't forget - in this corner we have a voting going - do you like this device or not(да-yes/нет-no)

And now Alex is announcing the giveaway which is for CIS countries

So while you are waiting for the final part - leave a comment - do you like the review/subtitles or just leave your opinion on this video

Also share the news that now subtitles are available with your friends

That's it friends

Don't forget to hit that Like button if you liked this review

Also don't forget to subscribe to my channel and share this video in your social network. Spread the word

And of course don't forget to push that Bell button so it will notify you when new video is up

Alex from VapersMD and Berserker MTL RDA was with you

We'll see you soon and poka poka

Oh yeah, i totally forgot to tell you about the price of this device. The price is gonna be about the same as all other devices from Vandy Vape

So search it in Chinese online stores and wait for it in your local vape shops

One more time - poka poka everybody

For more infomation >> BERSERKER MTL RDA l by Alex VapersMD & Vandy Vape l ENG SUBS l + РОЗЫГРЫШ 🚭🔞 - Duration: 16:48.

-------------------------------------------

ワンコの魚釣り!!狙いを定める鋭い目。一撃ぱっくりんちょ!?【ある意味感動】 - Duration: 2:26.

For more infomation >> ワンコの魚釣り!!狙いを定める鋭い目。一撃ぱっくりんちょ!?【ある意味感動】 - Duration: 2:26.

-------------------------------------------

[ラップ ビート] フリートラック "Bring It On" フリースタイル ビート [トラック提供] (オリジナルビート) - Duration: 2:25.

For more infomation >> [ラップ ビート] フリートラック "Bring It On" フリースタイル ビート [トラック提供] (オリジナルビート) - Duration: 2:25.

-------------------------------------------

Big Gummy Vs. Lil Gummy

For more infomation >> Big Gummy Vs. Lil Gummy

-------------------------------------------

APPROVATO E FINANZIATO PROGETTO PER BOCCA D'ENZA - Tg Parma 24/02/2018 - Duration: 1:20.

For more infomation >> APPROVATO E FINANZIATO PROGETTO PER BOCCA D'ENZA - Tg Parma 24/02/2018 - Duration: 1:20.

-------------------------------------------

Allerta maltempo 26 febbraio:scuole chiuse e gelo, ecco le previsioni choc - Duration: 3:28.

For more infomation >> Allerta maltempo 26 febbraio:scuole chiuse e gelo, ecco le previsioni choc - Duration: 3:28.

-------------------------------------------

Peugeot 108 1.0 e-VTi 68pk 5D TOP! Allure Automaat Leer - Duration: 1:02.

For more infomation >> Peugeot 108 1.0 e-VTi 68pk 5D TOP! Allure Automaat Leer - Duration: 1:02.

-------------------------------------------

Simone, dupla com Simaria, faz coreografia ousada e leva fãs ao delírio - Duration: 1:38.

For more infomation >> Simone, dupla com Simaria, faz coreografia ousada e leva fãs ao delírio - Duration: 1:38.

-------------------------------------------

Come sembrare più giovane con l'hairstyle - Duration: 3:50.

For more infomation >> Come sembrare più giovane con l'hairstyle - Duration: 3:50.

-------------------------------------------

Gli attacchi della mente: non arrenderti! (Mind Attacks — Don't Give Up!) - Duration: 6:12.

For more infomation >> Gli attacchi della mente: non arrenderti! (Mind Attacks — Don't Give Up!) - Duration: 6:12.

-------------------------------------------

#4 Blues Licks - Pentatonica Minore + 3maj - Duration: 2:22.

For more infomation >> #4 Blues Licks - Pentatonica Minore + 3maj - Duration: 2:22.

-------------------------------------------

Attenzione ai danni da mancanza di sonno. Ecco cosa accade al corpo quando non riesci a dormire - Duration: 4:42.

For more infomation >> Attenzione ai danni da mancanza di sonno. Ecco cosa accade al corpo quando non riesci a dormire - Duration: 4:42.

-------------------------------------------

BERSERKER MTL RDA l by Alex VapersMD & Vandy Vape l ENG SUBS l + РОЗЫГРЫШ 🚭🔞 - Duration: 16:48.

Again this tremor in hands, tremor in voice and certain uncertainty

Certain uncertainty...I can say like that.

Everytime when you do a presentation of a new device of your own, you are always uncertain how people will perceive it

What will reviewers say about it and what kind of opinion eventually will people have

I'm always very worried at such moments, that is why i will gladly read your comments below this video

So folks, let's not delay this exciting moment and let's roll. Intro...

Hello everyone! Alex from VapersMD is here

And i'm glad to welcome you on my channel

And today i will tell you about my new RDA, that i made in cooperation with Vandy Vape

Friends, this is this is a continuation of the line of Berserker MTL

This is Berserker MTL RDA

Single coil RDA with familiar posts, very deep juice well, with hot swap of airflow tubes feature, airflow adjustment options, top fill and also this RDA can easily work with squonk mods

it was made to be quite compact - only 18mm in diameter, but there were own reasons for it

Initially this RDA had 3 variants, and all of them was 22mm in diameter

They had different airflow adjustment, possibilities of change the airflow and other good features and options which i can't show you right now, since it's possible that we will use them in our other devices

In one RDA i didn't like the adjustment, in second RDA i didn't like the swap of the airflow tubes and in third i didn't like the noise this RDA produced

But one of the main cons, that all three of these devices has - it is minimal amount of flavor

So in the end there was made a decision to change the diameter of this RDA down to 18mm to reduce the chamber, to get correct flavor with MTL draw

And you know, in my opinion we are succeeded

Friends, i will not be delaying the moment of close up to show you massive kit and tell you how to launch this RDA

Let's dive down

Okay friends, let's get to the unboxing. I won't be focusing on the package since it's standard

And all of the kit contents we have on the desk

So in the kit we have an RDA itself

24mm decorative ring

22mm decorative ring

Coil correction tool for more convenient coil installation

That famous blue screwdriver. It must be here.

Allen key for squonk pin installation

Screw for negative post *note on the top - this is a screw for negative post*

Two spare post screws

Delrin top for drip tip since the drip tip is composite

Spare o-rings

Swappable airflow tubes

Pre-made coil, QC pass and User Manual

And now let's talk about specs. This RDA is made of stainless steel and available in 4 colors - steel, black, gold and rainbow

It have a slot for 510 drip tips, top cap for convenient refill, familiar posts for single coil installation, 6 swappable airflow tubes that is made of heatproof plastic with different holes and diameters

You can swap them when you have coil and cotton installed

Also airflow can be adjusted by turning the barrel

Juice well is 12.8mm deep

Main diameter of RDA is 18mm, but in the kit we have 2 decorative rings - 22 and 24mm

And now it's time for a detailed look and as always we start from the top

On the top we have 510 with heat sink, also this drip tip is composite and we have ultem cap

Top part is removable and its unscrews counter clockwise

You can easily swap it do delrin cap that we have in the kit

As i said it's 510 drip tip, it have 2 o-rings and inside it's cone shaped, the bore diameter is 3mm

Next we see the top cap which is for top fill. It have a knurling for convenient removing

Removing is easy and in the same moment it holds good due to correctly selected o-ring

On the inside it's cone shaped, which should positively affect the flavor

And of course you can install any of your favorite 510 drip tips into that slot

Next we see a perforated barrel. In it we have airflow holes - about the same amount as Berserker RTA, but one more (it's 6 holes)

So, it's 0.8mm, 1mm, 1.2mm, 1.4mm, 1.6mm and 2mm

And by turning this barrel you can adjust the airflow

This barrel is holds on 2 o-rings which is on the deck

And now let's talk about the deck itself. In here you can see a familiar posts, that was in Berserker MTL RTA, both in 24 and 22mm versions, with special walls for convenient coil installation and phillips head screws

I think you noticed those 2 big holes that we have in the deck. In these holes you will be inserting your airflow tubes

The airflow tube is look like so. One side have a hole for getting the air and in center it have a hole for blowing the coil. On the opposite side it's just blank plastic

As i said before in the kit we have 6 of these tubes with various holes and diameters

Okay, the smallest hole is 1.2mm

Next hole is 1.4mm

Third hole is 1.6mm

And fourth hole is 2mm

Also there is 2 non-standard tubes - one with 3 holes 1mm each and a stripe 3*0.5mm

So yes, friends, in here you have a lot of options to adjust the airflow and you can experiment as much as you want

Okay, let's see how the airflow tube is being inserted

Like i showed you there is two large through holes in the deck and you can insert this tube inside by a simple motion of the hand

Now it's Installed and centered and the tube sits in its groove

One side is blank and other side have a hole for getting the air

And now let's look how the deck look from the top. As you can see these holes are asymmetrical, it was made on purpose so it's be possible to fill the juice

Accordingly, when you have installed coil in here in the center will be the cotton. So you will be filling juice in both of these corners

Pay attention - this juice well is not divided, but it have slight deepenings for larger capacity

So when you fill it on one side, the juice will get to the other side

Also on the bottom we have sort of bridge, it is for spit-back protection while squonking. This is my sort of feature which i will be using almost in all of my RDA's

On the bottom it look like so. In here it's written Berserker MTL RDA, my logo, certificates, serial number and date of production and a line which says that manufacturer is Vandy Vape

Gold-plated screw that holds negative post and pin that holds positive post

This pin is adjustable. And in case it won't be long enough for you - you can unscrew it a bit

And if we continue unscrewing it, we will be able to install squonk pin

By unscrewing external pin we getting access to the main screw which holds positive post. We will also have to unscrew it

And after we will be able to install the squonk pin with allen key from the kit

In that simple way we are installing the squonk pin in this RDA

Okay friends, now we can use this RDA on squonk mods

This is good~

Moving forward, let's finish with a kit. In the kit we have 2 decorative rings - one is 24mm in diameter, other is 22mm in diameter

And it's pretty simple to use them - you will need one of them, depends on what diameter your mechanical mod or box mod is

Put that decorative ring on the bottom part of the RDA and after that screw the RDA on the box mod or mechanical mod

This is how it will look at box mods that is fit 22mm diameter atomizers

For understanding the size - at the left hand is Berserker 24mm and at the right hand is Berserker MTL RDA

Well, i think we saw enough so it's time to and launch it. Let's install the coil

The sequence of actions is important. Firstly - install the coil and glow it and after that you can insert the airflow tube

To prevent the plastic tubes from damaging by glowing coils

But friends, I can assure you - it's heatproof plastic and when you use the RDA as intended nothing's gonna happen to it

But when you glow the coil and temperature of it rise to the maximum - in that case even that heatproof plastic might not endure it

So again - install the coil, glow it and only after this insert the airflow tube

Okay folks, let's get to the coil installation. I will use the fused clapton coil from a kit

Also this wire can be purchased separately and it's named Superfine MTL Fused Clapton Wire

This wire is made by Vandy Vape, on the top it have parameters, so you can build a fused clapton like this by yourself

This wire is made of Nichrome

For a start let's unscrew the screws

Inner diameter of kit coil is 2.5mm, but i will add one more wrap

So in the end we got 6 visual wraps

And now is one of the important moments - we will install the coil the way that leads will be on top and the coil itself on the bottom

After that place the leads in those grooves and tighten it with screws

Now correct the coil and bend the leads into those notches on both sides

And cut it

Now let's glow it

After the glow is done we need the airflow tube

You know, i have 2 favorite airflow tubes that i like the most in terms of draw and flavor - the tube with the smallest hole and tube with oval-shaped hole

So i will be using a tube with oval-shaped hole

Let's insert it. As you can see on one side we have insulator - insert it from this side - that will be way more comfortable and it will sit more even

Some tubes inserts a little tighter, but by applying a little force you will succeed

And here you might need a Coil correction tool which is also included in the kit

That's written on the back of it: Coil correction tool

As you can see it's angled for convenient manipulation with the coil. On one side diameter is 3mm, on the other it's 2.5mm

After you've installed the coil, glowed it and inserted airflow tube you can lower the coil closer to the airflow to have like 1mm between them

Now i'm totally satisfied with the coil and it's time to put some cotton

I'm using standard Koh Gen Do cotton. I peeled off the upper layer and now it's ready

And now regarding the amount of cotton and how much we should left of it - i think that this will be enough

I'm eyeballing it, but to clarify - it's going down to like second o-ring

Friends, don't try to stuff a lot of cotton - otherwise you will not have a juice well. So a lot of cotton in this RDA is completely unnecessary

And now i'll do something for the first time, since i don't like doing it - i will thin the cotton and by doing so i will reduce its amount and size

I think that amount is enough. No more tortures on it

Now just put the cotton inside the juice well in standard way

Pay attention - on one side cotton is blocked all the holes, but we will shift it after saturation

Right now, when we saturate it, a little bit of juice can get into the airflow. I suggest you to insert the airflow tube in the latest moment. Well maybe after you've adjusted the position of your coil

So to prevent juice getting into the airflow we move the airflow tube to the side and now we can to fill it with no problems even in this barbaric way

Great. Now let's get back the airflow tube in place

And now just shift the cotton a bit to drip into the juice well with no problems

I can say, friends, this RDA holds up to 20 drops. I was experimenting and it's 20 or 21 drops with dry cotton

You can freely drip on either sides

Also this RDA is having sort of leak-proof system - it didn't leaked even once out of airflow, so you can fill it to the edge and it will not leak through the airflow

After this we will need the barrel. Match it with airflow hole

I selected the second hole, it have optimal draw for me

Keep in mind that airflow tube should sit flush with the deck, otherwise you'll be unable to put on the barrel

As you can see i did it from the first try. And i think it's time get back to face-time, vape it and speak a little bit

Final resistance is 0.78Ω, power is 13.5W - it will be enough

So thanks for your attention in close up, let's roll

It is what it is friends

It works and it's capable of giving proper MTL draw - both loose and tight draw

And for those of you who is going to ask what's this box mod - it's Series B powered by DNA75 from Jac Vapor

This mod is made in England, it might be said it's high-end, and later i will definitely make a review on it

But let's talk about RDA itself

I think this RDA come out quite universal. You can freely use it on box mods, also you can easily use it on squonk mods since it have BF pin

By the way, RDA with beauty ring that is 24mm diameter, is gonna look like so

Fit of this squonk mod is 24mm and i think it looks not bad

But we're moving forward. Also you can use this RDA on mechanical mods that is 22 and 24mm in diameter with no problems

It's looks so-so. Not for everybody, as the saying goes.

And of course you can use this RDA on Ego-style mods with diameter 18mm and 19mm

This Ego-style mod is made by Joyetech and this RDA works perfectly with it

So friends, that's how this RDA looks on different mods. But there is another moment that we tried to achieve

And that is hot swap of airflow tubes feature

in order for you to be able to swap the airflow tube even with installed coil and cotton inside and try this RDA with other type of draw or airflow

For that you just need to take off that barrel and it's no matter if you have beauty ring installed or not

Take the airflow tube from the kit and just insert it inside and replace the previous one

After that put on the barrel, match the hole of the airflow you need and vape

And you know, you get different experience with different airflow tubes - different draw and flavor is changing a bit

And here you have a field for experiments

Overall friends, i have many things that i could have told you, but there is one moment that i want to show you

It is how to refill this RDA if you don't use squonk mods

You just take off the top cap, and in that simple way you drip the juice inside. This RDA accommodates up to 20 drops

Total capacity of juice well with no cotton inside is 1.2ml of e-liquid

And after you done dripping, put the top cap back and continue to vape

That's how we roll, friends

Okay, we're going to finalize this review

I want to say big thanks to Vandy Vape

I really like working with this company. They are great, they are the top

They do everything like a Tsar and it's a pleasure to have a business with them

To you friends - big thanks for your attention

Don't forget - in this corner we have a voting going - do you like this device or not(да-yes/нет-no)

And now Alex is announcing the giveaway which is for CIS countries

So while you are waiting for the final part - leave a comment - do you like the review/subtitles or just leave your opinion on this video

Also share the news that now subtitles are available with your friends

That's it friends

Don't forget to hit that Like button if you liked this review

Also don't forget to subscribe to my channel and share this video in your social network. Spread the word

And of course don't forget to push that Bell button so it will notify you when new video is up

Alex from VapersMD and Berserker MTL RDA was with you

We'll see you soon and poka poka

Oh yeah, i totally forgot to tell you about the price of this device. The price is gonna be about the same as all other devices from Vandy Vape

So search it in Chinese online stores and wait for it in your local vape shops

One more time - poka poka everybody

For more infomation >> BERSERKER MTL RDA l by Alex VapersMD & Vandy Vape l ENG SUBS l + РОЗЫГРЫШ 🚭🔞 - Duration: 16:48.

-------------------------------------------

Factory Where Nuts Are Handled - Duration: 11:07.

For more infomation >> Factory Where Nuts Are Handled - Duration: 11:07.

-------------------------------------------

【MUKBANG】 Sakura Strawberry Pink Mochi Frappuccino! Starbucks 2018 Spring Items! 4005kcal [Use CC] - Duration: 7:28.

Hello it's Kinoshita Yuka (English subtitles by ~Aphexx~)

So today tadaa! Starbucks New Product Haul

spring (is about here) and so its filled with many KAWAII sakura themed products

just check this stuff out here its so pink

Also.... tadaa

this is made to resemble sakura as well its sakura (cherry blossom themed)

you can just feel the Hanami season about to begin (flower blossom watching)

itadakimasu starting off with this... pink sakura strawberry w/mochi frap

its got mochi in it ~ maybe? ~

yummy AF

its not really mochi like but rather more of a sakuramochi

its got bits of sakuramochi in it (pink mochi)

its got bits of chewy bits in it

its a drinkable frap with tiny ..... chewy bits in it

is it filled with mochi rice in here? ~ what exactly is in it I wonder ~

its a bit chewy and has a sakura flavor to it its Suuuper delish

its so exquisite and the sakuramochi flavor really permeates throughout the drink....

~ hey wait a minute it really tastes super delish... its so legit yummy ~

this is sakura strawberry ~piklm myulpi~

pink sakura strawberry milk latte

~ its really so tough to say ~

it doesn't really smell like anything much it smells like a latte

its a latte with a slight sakura and strawberry flavor its very yummy

a very mild sweetness

sakura strawberry pink tea

its a strawberry tea like aroma

The strawberries are so sweet and tangy its super yummy... its slighly on the sweet side

There's a slight amount of Sakura flavor to it

In total I have about 10 different food items I will start off with the warmer items

Hot salad wrap Mushroom soy curry

It's a wrap that you warm up

This is my first time trying out one of these

You can really smell the curry in this

The curry is so spicy With plenty of crunchy vegetables

Curry and veggies go so nicely together the taters are yummy

the lotus root is yummy as well

"ishigama" filone with lemon butter chicken

The stuff inside looks very yummy

The chicken is so juicy Its flavored with lemon and butter.... so yummy

The herbs give it a nice added mouthfeel It's so very yummy

Caramel toffee American Stone

It's slathered in caramel

It's even got chunks of caramel inside its gotten cold so I'mma go warm it up

It smells so wonderful The caramel is all melted

I heated it up too much And so I can't eat it right now

so first I'll have this strawberry cheesecake american scone

its so crisp and yummy its got a strawberry and cheesecake flavor to it

its so pink and lovely

its so nice after warming up the caramel is all melted and yummy

next sakura donut

its covered in strawberry chocolate and its so yummy the donut is so moist and chewy

custard cream rolled pie it looks like this and filled with cream

within a crisp pie crust its filled with a light creamy custard

the crust surrounding it is so crispy and the cream is so smooth and creamy

I really enjoy the contrast between the 2 next is a fruity cheesecake

there are all sorts of dried fruit floating in the rare cheesecake. making for an interesting mouthfeel

the rarecheese is so smooth and melts in your mouth nicely I love the mouthfeel

sakura chiffon cake its got a sakura blossom on it... so kawaii

its so fluffy

I love that chewy sakura flavored cake the cream is very yummy

the flower has been pickled

milk pudding and matcha cream pudding

the milk pudding is a new product there were many items at my starbucks

they weren't sold out and they had plenty of supplies and most of everything showcased on their website

was available in store starting with the matcha one

this is what it looks like its such a nice green color

the pink and green is nice its so jiggly

the matcha flavor is so rich

Going further there is matcha syrup inside

Further increasing the matcha flavor

Now for the milk pudding This is what it looks like inside

It's so very creamy

It's very milky with a white chocolate flavor And some caramel as well

It's made even yummier with The caramel

last mouthful itadakimasu

gochisosamadeshita

The new product line from Starbucks Was so yummy

As you'll see I've got two of these drinks leftover

And since I was eating 10 of their food product line I thought I'd run outta something to drink

and so I bought my faves... white mocha and hot cocoa and I was able to eat everything without them

So I will Savor them slowly While editing this video

You can really tell that spring is about to come

....... but its cold AF still

Want you all get a jump on Hanami season And take a trip to starbucks?

Your eyes and tummy will thank you

For everyone else won't you all please give it a try At as always thank you for watching if there's anything you

Want me to do or eat please tell me in the comment section below if you like this video please hit the like And subscribe buttons

oh yeah.... a viewer told me to sakura starb~~~~

wait no... its not sakura starbucks....

There are many Sakura products at starbucks so please give them a try.... TYVM

laterz BAI BAI

For more infomation >> 【MUKBANG】 Sakura Strawberry Pink Mochi Frappuccino! Starbucks 2018 Spring Items! 4005kcal [Use CC] - Duration: 7:28.

-------------------------------------------

Half-dried Herrings Mukbang - Duration: 11:18.

For more infomation >> Half-dried Herrings Mukbang - Duration: 11:18.

-------------------------------------------

10 Very cool things for school with Aliexpress! [FUN LIFE] - Duration: 4:08.

For more infomation >> 10 Very cool things for school with Aliexpress! [FUN LIFE] - Duration: 4:08.

-------------------------------------------

Maria De Filippi rimprovera Tina Cipollari: ecco cos'ha detto a UeD - Duration: 4:04.

For more infomation >> Maria De Filippi rimprovera Tina Cipollari: ecco cos'ha detto a UeD - Duration: 4:04.

-------------------------------------------

Isola: la Henger supera il test della verità circa il clamoroso 'Canna-gate' - Duration: 3:37.

For more infomation >> Isola: la Henger supera il test della verità circa il clamoroso 'Canna-gate' - Duration: 3:37.

-------------------------------------------

Una Vita anticipazioni: Mauro spara a Cayetana? Puntata 545 - Duration: 3:07.

For more infomation >> Una Vita anticipazioni: Mauro spara a Cayetana? Puntata 545 - Duration: 3:07.

-------------------------------------------

Jaguar F-Pace 2.0D R-SPORT AWD / LED / BLACK PACK - Duration: 0:54.

For more infomation >> Jaguar F-Pace 2.0D R-SPORT AWD / LED / BLACK PACK - Duration: 0:54.

-------------------------------------------

Volvo XC60 D3 R-Design Automaat 20 Inch Navi Leder PDC V&A - Duration: 0:56.

For more infomation >> Volvo XC60 D3 R-Design Automaat 20 Inch Navi Leder PDC V&A - Duration: 0:56.

-------------------------------------------

Renault Captur TCe 90pk Dynamique (CAMERA!!!/R-link/Climate/Cruise/PDC/17''LMV) - Duration: 1:01.

For more infomation >> Renault Captur TCe 90pk Dynamique (CAMERA!!!/R-link/Climate/Cruise/PDC/17''LMV) - Duration: 1:01.

-------------------------------------------

The Door and Window Security Bar - Duration: 14:16.

For more infomation >> The Door and Window Security Bar - Duration: 14:16.

-------------------------------------------

BERSERKER MTL RDA l by Alex VapersMD & Vandy Vape l ENG SUBS l + РОЗЫГРЫШ 🚭🔞 - Duration: 16:48.

Again this tremor in hands, tremor in voice and certain uncertainty

Certain uncertainty...I can say like that.

Everytime when you do a presentation of a new device of your own, you are always uncertain how people will perceive it

What will reviewers say about it and what kind of opinion eventually will people have

I'm always very worried at such moments, that is why i will gladly read your comments below this video

So folks, let's not delay this exciting moment and let's roll. Intro...

Hello everyone! Alex from VapersMD is here

And i'm glad to welcome you on my channel

And today i will tell you about my new RDA, that i made in cooperation with Vandy Vape

Friends, this is this is a continuation of the line of Berserker MTL

This is Berserker MTL RDA

Single coil RDA with familiar posts, very deep juice well, with hot swap of airflow tubes feature, airflow adjustment options, top fill and also this RDA can easily work with squonk mods

it was made to be quite compact - only 18mm in diameter, but there were own reasons for it

Initially this RDA had 3 variants, and all of them was 22mm in diameter

They had different airflow adjustment, possibilities of change the airflow and other good features and options which i can't show you right now, since it's possible that we will use them in our other devices

In one RDA i didn't like the adjustment, in second RDA i didn't like the swap of the airflow tubes and in third i didn't like the noise this RDA produced

But one of the main cons, that all three of these devices has - it is minimal amount of flavor

So in the end there was made a decision to change the diameter of this RDA down to 18mm to reduce the chamber, to get correct flavor with MTL draw

And you know, in my opinion we are succeeded

Friends, i will not be delaying the moment of close up to show you massive kit and tell you how to launch this RDA

Let's dive down

Okay friends, let's get to the unboxing. I won't be focusing on the package since it's standard

And all of the kit contents we have on the desk

So in the kit we have an RDA itself

24mm decorative ring

22mm decorative ring

Coil correction tool for more convenient coil installation

That famous blue screwdriver. It must be here.

Allen key for squonk pin installation

Screw for negative post *note on the top - this is a screw for negative post*

Two spare post screws

Delrin top for drip tip since the drip tip is composite

Spare o-rings

Swappable airflow tubes

Pre-made coil, QC pass and User Manual

And now let's talk about specs. This RDA is made of stainless steel and available in 4 colors - steel, black, gold and rainbow

It have a slot for 510 drip tips, top cap for convenient refill, familiar posts for single coil installation, 6 swappable airflow tubes that is made of heatproof plastic with different holes and diameters

You can swap them when you have coil and cotton installed

Also airflow can be adjusted by turning the barrel

Juice well is 12.8mm deep

Main diameter of RDA is 18mm, but in the kit we have 2 decorative rings - 22 and 24mm

And now it's time for a detailed look and as always we start from the top

On the top we have 510 with heat sink, also this drip tip is composite and we have ultem cap

Top part is removable and its unscrews counter clockwise

You can easily swap it do delrin cap that we have in the kit

As i said it's 510 drip tip, it have 2 o-rings and inside it's cone shaped, the bore diameter is 3mm

Next we see the top cap which is for top fill. It have a knurling for convenient removing

Removing is easy and in the same moment it holds good due to correctly selected o-ring

On the inside it's cone shaped, which should positively affect the flavor

And of course you can install any of your favorite 510 drip tips into that slot

Next we see a perforated barrel. In it we have airflow holes - about the same amount as Berserker RTA, but one more (it's 6 holes)

So, it's 0.8mm, 1mm, 1.2mm, 1.4mm, 1.6mm and 2mm

And by turning this barrel you can adjust the airflow

This barrel is holds on 2 o-rings which is on the deck

And now let's talk about the deck itself. In here you can see a familiar posts, that was in Berserker MTL RTA, both in 24 and 22mm versions, with special walls for convenient coil installation and phillips head screws

I think you noticed those 2 big holes that we have in the deck. In these holes you will be inserting your airflow tubes

The airflow tube is look like so. One side have a hole for getting the air and in center it have a hole for blowing the coil. On the opposite side it's just blank plastic

As i said before in the kit we have 6 of these tubes with various holes and diameters

Okay, the smallest hole is 1.2mm

Next hole is 1.4mm

Third hole is 1.6mm

And fourth hole is 2mm

Also there is 2 non-standard tubes - one with 3 holes 1mm each and a stripe 3*0.5mm

So yes, friends, in here you have a lot of options to adjust the airflow and you can experiment as much as you want

Okay, let's see how the airflow tube is being inserted

Like i showed you there is two large through holes in the deck and you can insert this tube inside by a simple motion of the hand

Now it's Installed and centered and the tube sits in its groove

One side is blank and other side have a hole for getting the air

And now let's look how the deck look from the top. As you can see these holes are asymmetrical, it was made on purpose so it's be possible to fill the juice

Accordingly, when you have installed coil in here in the center will be the cotton. So you will be filling juice in both of these corners

Pay attention - this juice well is not divided, but it have slight deepenings for larger capacity

So when you fill it on one side, the juice will get to the other side

Also on the bottom we have sort of bridge, it is for spit-back protection while squonking. This is my sort of feature which i will be using almost in all of my RDA's

On the bottom it look like so. In here it's written Berserker MTL RDA, my logo, certificates, serial number and date of production and a line which says that manufacturer is Vandy Vape

Gold-plated screw that holds negative post and pin that holds positive post

This pin is adjustable. And in case it won't be long enough for you - you can unscrew it a bit

And if we continue unscrewing it, we will be able to install squonk pin

By unscrewing external pin we getting access to the main screw which holds positive post. We will also have to unscrew it

And after we will be able to install the squonk pin with allen key from the kit

In that simple way we are installing the squonk pin in this RDA

Okay friends, now we can use this RDA on squonk mods

This is good~

Moving forward, let's finish with a kit. In the kit we have 2 decorative rings - one is 24mm in diameter, other is 22mm in diameter

And it's pretty simple to use them - you will need one of them, depends on what diameter your mechanical mod or box mod is

Put that decorative ring on the bottom part of the RDA and after that screw the RDA on the box mod or mechanical mod

This is how it will look at box mods that is fit 22mm diameter atomizers

For understanding the size - at the left hand is Berserker 24mm and at the right hand is Berserker MTL RDA

Well, i think we saw enough so it's time to and launch it. Let's install the coil

The sequence of actions is important. Firstly - install the coil and glow it and after that you can insert the airflow tube

To prevent the plastic tubes from damaging by glowing coils

But friends, I can assure you - it's heatproof plastic and when you use the RDA as intended nothing's gonna happen to it

But when you glow the coil and temperature of it rise to the maximum - in that case even that heatproof plastic might not endure it

So again - install the coil, glow it and only after this insert the airflow tube

Okay folks, let's get to the coil installation. I will use the fused clapton coil from a kit

Also this wire can be purchased separately and it's named Superfine MTL Fused Clapton Wire

This wire is made by Vandy Vape, on the top it have parameters, so you can build a fused clapton like this by yourself

This wire is made of Nichrome

For a start let's unscrew the screws

Inner diameter of kit coil is 2.5mm, but i will add one more wrap

So in the end we got 6 visual wraps

And now is one of the important moments - we will install the coil the way that leads will be on top and the coil itself on the bottom

After that place the leads in those grooves and tighten it with screws

Now correct the coil and bend the leads into those notches on both sides

And cut it

Now let's glow it

After the glow is done we need the airflow tube

You know, i have 2 favorite airflow tubes that i like the most in terms of draw and flavor - the tube with the smallest hole and tube with oval-shaped hole

So i will be using a tube with oval-shaped hole

Let's insert it. As you can see on one side we have insulator - insert it from this side - that will be way more comfortable and it will sit more even

Some tubes inserts a little tighter, but by applying a little force you will succeed

And here you might need a Coil correction tool which is also included in the kit

That's written on the back of it: Coil correction tool

As you can see it's angled for convenient manipulation with the coil. On one side diameter is 3mm, on the other it's 2.5mm

After you've installed the coil, glowed it and inserted airflow tube you can lower the coil closer to the airflow to have like 1mm between them

Now i'm totally satisfied with the coil and it's time to put some cotton

I'm using standard Koh Gen Do cotton. I peeled off the upper layer and now it's ready

And now regarding the amount of cotton and how much we should left of it - i think that this will be enough

I'm eyeballing it, but to clarify - it's going down to like second o-ring

Friends, don't try to stuff a lot of cotton - otherwise you will not have a juice well. So a lot of cotton in this RDA is completely unnecessary

And now i'll do something for the first time, since i don't like doing it - i will thin the cotton and by doing so i will reduce its amount and size

I think that amount is enough. No more tortures on it

Now just put the cotton inside the juice well in standard way

Pay attention - on one side cotton is blocked all the holes, but we will shift it after saturation

Right now, when we saturate it, a little bit of juice can get into the airflow. I suggest you to insert the airflow tube in the latest moment. Well maybe after you've adjusted the position of your coil

So to prevent juice getting into the airflow we move the airflow tube to the side and now we can to fill it with no problems even in this barbaric way

Great. Now let's get back the airflow tube in place

And now just shift the cotton a bit to drip into the juice well with no problems

I can say, friends, this RDA holds up to 20 drops. I was experimenting and it's 20 or 21 drops with dry cotton

You can freely drip on either sides

Also this RDA is having sort of leak-proof system - it didn't leaked even once out of airflow, so you can fill it to the edge and it will not leak through the airflow

After this we will need the barrel. Match it with airflow hole

I selected the second hole, it have optimal draw for me

Keep in mind that airflow tube should sit flush with the deck, otherwise you'll be unable to put on the barrel

As you can see i did it from the first try. And i think it's time get back to face-time, vape it and speak a little bit

Final resistance is 0.78Ω, power is 13.5W - it will be enough

So thanks for your attention in close up, let's roll

It is what it is friends

It works and it's capable of giving proper MTL draw - both loose and tight draw

And for those of you who is going to ask what's this box mod - it's Series B powered by DNA75 from Jac Vapor

This mod is made in England, it might be said it's high-end, and later i will definitely make a review on it

But let's talk about RDA itself

I think this RDA come out quite universal. You can freely use it on box mods, also you can easily use it on squonk mods since it have BF pin

By the way, RDA with beauty ring that is 24mm diameter, is gonna look like so

Fit of this squonk mod is 24mm and i think it looks not bad

But we're moving forward. Also you can use this RDA on mechanical mods that is 22 and 24mm in diameter with no problems

It's looks so-so. Not for everybody, as the saying goes.

And of course you can use this RDA on Ego-style mods with diameter 18mm and 19mm

This Ego-style mod is made by Joyetech and this RDA works perfectly with it

So friends, that's how this RDA looks on different mods. But there is another moment that we tried to achieve

And that is hot swap of airflow tubes feature

in order for you to be able to swap the airflow tube even with installed coil and cotton inside and try this RDA with other type of draw or airflow

For that you just need to take off that barrel and it's no matter if you have beauty ring installed or not

Take the airflow tube from the kit and just insert it inside and replace the previous one

After that put on the barrel, match the hole of the airflow you need and vape

And you know, you get different experience with different airflow tubes - different draw and flavor is changing a bit

And here you have a field for experiments

Overall friends, i have many things that i could have told you, but there is one moment that i want to show you

It is how to refill this RDA if you don't use squonk mods

You just take off the top cap, and in that simple way you drip the juice inside. This RDA accommodates up to 20 drops

Total capacity of juice well with no cotton inside is 1.2ml of e-liquid

And after you done dripping, put the top cap back and continue to vape

That's how we roll, friends

Okay, we're going to finalize this review

I want to say big thanks to Vandy Vape

I really like working with this company. They are great, they are the top

They do everything like a Tsar and it's a pleasure to have a business with them

To you friends - big thanks for your attention

Don't forget - in this corner we have a voting going - do you like this device or not(да-yes/нет-no)

And now Alex is announcing the giveaway which is for CIS countries

So while you are waiting for the final part - leave a comment - do you like the review/subtitles or just leave your opinion on this video

Also share the news that now subtitles are available with your friends

That's it friends

Don't forget to hit that Like button if you liked this review

Also don't forget to subscribe to my channel and share this video in your social network. Spread the word

And of course don't forget to push that Bell button so it will notify you when new video is up

Alex from VapersMD and Berserker MTL RDA was with you

We'll see you soon and poka poka

Oh yeah, i totally forgot to tell you about the price of this device. The price is gonna be about the same as all other devices from Vandy Vape

So search it in Chinese online stores and wait for it in your local vape shops

One more time - poka poka everybody

For more infomation >> BERSERKER MTL RDA l by Alex VapersMD & Vandy Vape l ENG SUBS l + РОЗЫГРЫШ 🚭🔞 - Duration: 16:48.

-------------------------------------------

ワンコの魚釣り!!狙いを定める鋭い目。一撃ぱっくりんちょ!?【ある意味感動】 - Duration: 2:26.

For more infomation >> ワンコの魚釣り!!狙いを定める鋭い目。一撃ぱっくりんちょ!?【ある意味感動】 - Duration: 2:26.

-------------------------------------------

[ラップ ビート] フリートラック "Bring It On" フリースタイル ビート [トラック提供] (オリジナルビート) - Duration: 2:25.

For more infomation >> [ラップ ビート] フリートラック "Bring It On" フリースタイル ビート [トラック提供] (オリジナルビート) - Duration: 2:25.

-------------------------------------------

How I Make Money Online

For more infomation >> How I Make Money Online

-------------------------------------------

Opel Corsa 1.0T 66KW/90PK 3D EDITION - Duration: 0:54.

For more infomation >> Opel Corsa 1.0T 66KW/90PK 3D EDITION - Duration: 0:54.

-------------------------------------------

Opel Corsa 1.0T Online Edition 5D - Duration: 1:01.

For more infomation >> Opel Corsa 1.0T Online Edition 5D - Duration: 1:01.

-------------------------------------------

Opel Corsa 1.0T 90PK 5D Edition BLUETOOTH - Duration: 1:00.

For more infomation >> Opel Corsa 1.0T 90PK 5D Edition BLUETOOTH - Duration: 1:00.

-------------------------------------------

Gli attacchi della mente: non arrenderti! (Mind Attacks — Don't Give Up!) - Duration: 6:12.

For more infomation >> Gli attacchi della mente: non arrenderti! (Mind Attacks — Don't Give Up!) - Duration: 6:12.

-------------------------------------------

Opel Corsa 1.0T 90PK 5D Edition BLUETOOTH - Duration: 0:59.

For more infomation >> Opel Corsa 1.0T 90PK 5D Edition BLUETOOTH - Duration: 0:59.

-------------------------------------------

Disney Cars 3 movie toys track Ultimate Florida Playset Fun Playtime Surprise toys video for kids - Duration: 5:15.

Disney Cars 3 movie toys track Ultimate Florida Playset Fun Playtime Surprise toys video for kids

For more infomation >> Disney Cars 3 movie toys track Ultimate Florida Playset Fun Playtime Surprise toys video for kids - Duration: 5:15.

-------------------------------------------

South Korea praised for hosting successful PyeongChang Winter Olympics - Duration: 3:11.

There was some concern ahead of the PyeongChang Olympics.

The extreme cold, some Olympians worried about security... and at the last minute arranging

for North Korea to send its athletes and officials.

But as our Lee Ji-won reports, the overwhelming majority of visitors and spectators say the

Games were a success.

Here's a look at some of the highs and lows.

From tears of joy, sighs of disappointment to exhilarating excitement.

The past 17 days of the PyeongChang Winter Olympics were packed with incident and raw

emotions.

Now that the event is over, many are looking back at their February in South Korea's alpine

town of Pyeongchang and the sub-host city of Gangneung.

Many commented on how it was a huge success.

"I have been to 16 Olympics, winter and summer, and I thought this was one of the best ones

I've been to in terms of organization, logistics, the quality of the infrastructure.

You want to be as easy as possible to move around and to enjoy the games."

The friendliness of the locals and volunteers was also praised.

"We've been really impressed by how nice all the locals have been to us, especially patient,

because we don't speak any Korean, and even with the very wide language barrier everyone's

been really accommodating."

Of the many highlights was North Korea's participation in the Games.

While the decision and process was initially controversial, people say these exchanges

prove the Olympics is more than just a sporting event.

"Not just bold, but I think it's sent a message to the world and there's really only one place

that could do that and that is here in South Korea and here in Pyeongchang.

A lot of people say that's politics hijacking the games, no actually, this is a not a story

about politics, this is a story about people."

The bone-chilling temperatures during the Games was a major concern and it caused a

number of snow events to be postponed.

But journalists who've covered numerous Winter Olympics say cold is not a problem for winter

sports.

"Olympics are so big, there are always going to be issues.

In terms of the weather, it was very cold the first week, but in a way, this is the

Winter Olympics, they are supposed to be cold."

Visitors also suggested room for improvements.

"I think they should've taught English to most of the work force because I don't speak

Korean and as a foreigner it was hard for me to get information."

"It wasn't that expensive to book a place to stay, but I came here to watch numerous

events on different days... and there weren't many vacancies."

With the general consensus that the PyeongChang Olympics were a success, many visitors said

one of the best legacies of the Games is that South Korea "took a step forward in presenting

itself" to the world and the world got to know Korea better as well.

Lee Ji-won, Arirang News, Pyeongchang.

For more infomation >> South Korea praised for hosting successful PyeongChang Winter Olympics - Duration: 3:11.

-------------------------------------------

UNKNOWN NIGHT FURY / NEW TOOTHLESS? - Duration: 5:49.

Hello, everyone.

Today I will tell you about the Night Fury.

I'm not gonna tell you what you already know.

For example, that Fury is the product of death,

that Toothless is the only known member of this species.

And so on.

You already know everything.

Today I want to talk about some unknown

facts (because I have the TORGNIR's lost diaries)

and also about their guesses.

For example, why does Fury have teeth that are drawn into the gums?

Why would he?

To show their friendliness?

But why do this dragon show his benevolence,

and to whom?

And can be after all simply smile.

Therefore, I do not understand why evolution gave the dragon

such a feature.

But in the TORGNIR's diaries there's something about it

and in the end of the video I'll tell you about it…

But I'll start with some features of the body.

For example, we all know that Night Fury is a very

fast and maneuverable dragon.

But why?

Stormcutter is the fourwings dragon.

But the Fury has also 4 wing, they're just a little less

are a little behind the main wings.

But it's better like Stormcutter .

After all, each type of wing performs its task.

For example, the main wings of the Night Fury is very large

relative to the proportions of the body

body – they are responsible for the speed and planning of the dragon.

But the second wings help Fury to maneuver in flight,

to hang vertically in the air and to stabilize

its position.

A tail flaps allow the dragon to sharply change the direction

of flight and also stabilize its position – so

it can not fly without them.

The Night Fury is a fast and maneuverable dragon because he has 4 wings

and two tail flaps.

Fury has 8 ears.

But only two (the biggest) are the same

ears as ours.

He hears the usual sound by them.

But the rest of the ears are special.

They catch high and low frequencies of ultrasound

and infrasound.

Some ears like the sound of catch I cannot answer.

But, most likely, the upper ears are designed

for ultrasonic vibrations, and the lower and short

for infra.

So the dragon can catch any sounds of nature.

Now I want to tell you about claws of the Night Fury.

I rather that he doesn't have claws...

He certainly has something on the feet.

But it's not the claws.

I'd call them fingers.

I will explain why.

The claw is a corneal formation of cutaneous origin

on the phalanx of the finger.

The claw is a process that is very often dead.

And no creature on earth can bend its

claw.

And look what does Toothless do?

He bends the claw ...

because it's not a claw.

It is a finger with two phalanges, of which the inside is

a joint.

It is possible that at first the Fury had claws.

But they evolve and soon turn into fingers.

So, what kind of dragon is the Night Fury?

Why do we know Toothless only?

Where are the rest Furies?

Interestingly, the records of the TORGNIR have the following

information.

Now I will give you a literal translation from the ancient viking's language.

"When I finally reached this island in a week,

I was already late.

The Berserkers came to the island before me – what I saw

was terrible - they exterminated all the dragons on the island.

And I saw they caught and put in a cage dragon,

which I had not seen before

– dragon all sparkled and it seemed that will begin to let

the lightnings.

But it was just a feeling.

After all, dragons can't make lightning.

Only the great THOR is capable of that.

And when I left the island, I noticed little baby

dragons.

Their was 4.

They were still quite small, black with big

green eyes.

And Yes, they had no teeth at all.

What kind of dragons are they?

They must find it difficult to survive in nature.

I took them with me.

Unfortunately, I couldn't save them.

Three days later, I fell into the trap of the Berserkers,

and I had to let them go – I left them in the woods.

They are small and defenseless and they certainly could not

survive....»

I'm willing to bet that it was a Night Fury.

And, it seems that the Night Fury teeth begin to erupt

only in adolescence.

And two of the Furies definitely survived: the Toothless of Hiccup and Nibbler,

who fights in the tournament.

And it is possible that there is still the Furies

on earth.

A faithful record Torgnir and my assumptions or not – we will

know in the third part of the How to train your dragon.

Do you want to learn a lot about other dragons,

go to the play list UNKNOWN DRAGONS

and watch the tournament, where the NIBBLER is fighting.

Soon the finals of the tournament.

Well that's it for today.

In the next video, I'm going to tell you about the Screaming Death...

and I bet I'm going to tell you something

you didn't even know.

See you later.

For more infomation >> UNKNOWN NIGHT FURY / NEW TOOTHLESS? - Duration: 5:49.

-------------------------------------------

FBI's Text Messages Have Been Found, Look Who Is In Deep Sit Now - Duration: 14:20.

FBI's Text Messages Have Been Found, Look Who Is In Deep S*it Now

Somebody is in deep trouble now, because apparently on Thursday, Federal investigators said they

recovered at least some of the supposedly missing text messages between Peter Strzok

and Lisa Page.

Justice Department Inspector General Michael Horowitz told Congress told congress that

his investigators were able to recover some of the texts that had apparently disappeared

due to a phone "malfunction."

The two agents displayed a clear dislike towards Trump, and a clear preference to Hillary Clinton,

while they were working on both of their cases as FBI investigators.

Republicans had been wondering how the messages could have possibly disappeared, but FBI officials

claimed that a malfunction cause some of the texts to be deleted.

Text between the two in October of 2016, talking about a Wall Street Journal article that detailed

the conflict of interest it was to have FBI Director Andrew McCabe working on the case,

when his wife received a half a million dollar donation from the Clinton foundation.

The Wall Street Journal reported that 98 percent of that money was donated after the FBI started

the Clinton investigation.

Texts between the two agents shows that FBI Chief of Staff James Rybicki believes that

McCabe should have recused himself from the investigation, McCabe didn't recuse himself

until one week from the presidential election.

"RYBICKI JUST CALLED TO CHECK IN," MS.

PAGE SAID IN THE TEXT.

"HE VERY CLEARLY 100 PERCENT BELIEVES THAT ANDY SHOULD BE RECUSED BECAUSE OF THE 'PERCEPTION.'

"

Ms. Page then says, "If its a matter similar to those we've been talking about lately,

why no recusal before?"

"I ASSUME MCAULIFFE PICKED UP," MR.

STRZOK RESPONDED.

"BUT THAT DOESN'T MAKE SENSE.

HE SAID HE WAS INTERVIEWING, MAYBE HE'S HEADED INTO PRIVATE PRACTICE."

Page also added in a text that they might want to take it easy on Clinton.

"One more thing: she might be our next president.

The last thing you need us going in there loaded for bear," Ms. Page said in the text.

Michael Horowitz, the inspector general, told two senior Republican senators, Charles Grassley

and Ron Johnson, about the discovery, the Washington Examiner reported.

It came after mounting pressure – including from President Donald Trump – on the FBI

to find the cache of as many as 50,000 messages between the two.

The already uncovered messages have sent shockwaves through Washington, with the two calling Trump

'an idiot' and suggesting the FBI decided not to charge Hillary Clinton long before

the end of her secret server probe.

The contents of the new ones is not being published.

Attorney General Jeff Sessions had ordered an investigation by the inspector general

into the missing text messages on Tuesday.

Texts between senior counter-terrorism agent Strzok and FBI lawyer Page exchanged between

Dec. 14, 2016, and May 17, 2017, had been among a broader batch of missing phone messages

that the FBI says its system failed to store because of a software upgrade glitch which

affected Samsung 5 cellphones it issued to staff.

h/t Daily Mail

For more infomation >> FBI's Text Messages Have Been Found, Look Who Is In Deep Sit Now - Duration: 14:20.

-------------------------------------------

Do you know what a water main tapping is? - Duration: 2:15.

Hey guys.

Ben here.

Geelong Cable Locations.

Thought I'd do a quick little video to show you something you probably don't see

all the time.

If you're working in the construction industry

especially if you're a plumber you'll know this.

You don't need to watch this video.

But for those of you that are homeowners those of you that don't deal with this sort

of stuff at all.

I want to show you what a water connection looks like.

What a water connection from the house how it connects into the main.

We haven't done a shell but it's come past but we're working at

the house next to it here and I saw it dug up, someone's already exposed it.

So it's just called a water tap in.

And I'll just show you what it looks like.

Come and have a look.

So, the black pipe there is your water main.

That is the water main itself.

And see the connection in?

See the copper pipe?

That is a connection to the house.

So the house, the water meter is

just there.

So it goes from the water meter so the tap side of the water meter

is where it connects into the main.

So it goes from the water meter

over

and then dives down into the main.

If you have a look in there you'll see the the tapping itself.

Zoom in

That is how the water itself is connected to the main.

So that is your water main there and that's the connection going over to the house.

And you'll see over there that is a telephone conduit

and there's a new sleeve over the conduit because I reckon they've hit it.

They've dug when they've dug down they've damaged it

and they've put a new sleeve over it to fix it

protect it.

So yeah, for those of you that work in the construction industry

or plumbers I should say you'll see this sort of stuff all the time.

So, this won't matter to you.

But for those of you that are homeowners or those of you that don't

have never seen a tap in before that is what it looks like.

Alright, a bit of knowledge for you that you can now take away.

Guys, hope you're having a good day and we'll catch you on the next video.

Bye.

For more infomation >> Do you know what a water main tapping is? - Duration: 2:15.

-------------------------------------------

Japan Vlog #3 北海道吃吃吃+滑雪!|| Hokkaido Soup Curry! Snowboarding! - Duration: 6:35.

For more infomation >> Japan Vlog #3 北海道吃吃吃+滑雪!|| Hokkaido Soup Curry! Snowboarding! - Duration: 6:35.

-------------------------------------------

MP Barabbas Loins: No hard feelings - Duration: 1:42.

For more infomation >> MP Barabbas Loins: No hard feelings - Duration: 1:42.

-------------------------------------------

Doctors Urge Schools to Make Condoms Avaialble to Teens - Duration: 1:58.

Doctors Urge Schools to Make Condoms Avaialble to Teens.

In an updated policy statement, its first since 2001, the American

American

academy of pediatrics is recommending that schools make condoms available to teenagers

alongside providing instruction on sexual education topics

more from Reuters there is still some resistance to making condoms more accessible for young people

researchers said I think one of the main issue since the idea that if you provide condoms and make them accessible

kids will be more likely to have sex

that really that's not the case

Amy Bleakley said getting over the perception that giving condoms that will make kids have sex is a real hairier for parents and school

administrators she told Reuters Health bleakly studies teen sexual behavior and reproductive health at the University of Pennsylvania in

Philadelphia but wasn't part of the apt committee

she said some studies suggest teenagers with a access to condoms and comprehensive sex

education actually start having sex later than their peers who don't

teen birth rates have been declining in the United States according to the centers for disease control and prevention

in 2011

there were 31 berths for every 1000 U.S. women aged 15 to 19

that that number is still higher than in other developed countries

rates of many sexually transmitted infections SDI is holding committee at and gonorrhea are

also the highest among teenage and young adult women

For more infomation >> Doctors Urge Schools to Make Condoms Avaialble to Teens - Duration: 1:58.

-------------------------------------------

2 Easy Ways To GROW Your EYEBROWS Naturally & 10x FAST | Anaysa - Duration: 2:57.

Hi guys !!!!! I am Anishka

welcome to my channel ANAYSA...

you guys have seen lots of videos

for growing your eyebrows thicker

and also you had tried lots of home remedies

and you guys won't able to follow that

because of it's daily making and applying process

so today I am gonna share with you guys

2 special home remedies which you can store and use daily

ingredients i have used in this remedy

will help your eyebrows grow 2 time thicker

in couple of week you will see the very effective results

let's get started with today's video

for 1st remedy we need

you can get that from market or you can make at home too

put both the things in a bowl and mix them well

and make well consistency

here is ready our first remedy

for second remedy we need

put them in a bowl and mix them well

here is ready our second remedy

now i will tell you how to use this

do wash your face before using remedy

from both of these which one you are using

get that on your fingers and apply on your eyebrows

after applying do massage for 5 - 10 minutes gently

castor oil contains fatty acid, minerals and nutrients

which helps a lot for growth

hibiscus powder is a magical ingredient for hair growth

it also helps to grow your hair

after massage use and brush for brushing your eyebrow's hair

as shown in video

doing this it will help for improve your blood circulation

and help in eyebrow's growth too

aloe vera gel contains enzymes and moisturizing properties

which nourish hair pholicouls and helps for increase hair growth

lavender oil unlock skin pores and pores will get fresh air

and also helps to growth hair pholicals

apply this every night before sleeping

leave it over night

these were 2 magical remedy

you can use any one of them

you will get the results with couple of days

this was today's video

do like and share if you like it

also don't forget to subscribe anaysa

hit on bell icon too

comments below

me ANISHKA will meet you in my next video

till then take care and buhbyeeeee

For more infomation >> 2 Easy Ways To GROW Your EYEBROWS Naturally & 10x FAST | Anaysa - Duration: 2:57.

-------------------------------------------

Baekhyun Discusses EXO's "Nation's Pick" Nickname, Upcoming Olympics Performance, And More - Duration: 4:36.

Baekhyun Discusses EXO's "Nation's Pick" Nickname, Upcoming Olympics Performance, And More

EXOs Baekhyun participated in a phone interview with JTBCs Morning& news segment on February 23 to talk about the groups upcoming performance at the 2018 PyeongChang Winter Olympics closing ceremony.

On how he feels about the upcoming performance, Baekhyun stated, All of us were so happy when we were told that wed be performing at the closing ceremony.

Its an event that is watched by the entire world, so it is a great honor for us.

Its a stage of dreams that not many get the opportunity to participate in.

As well be representing K-pop through our performance, weve been holding a lot of discussions about our stage..

Soompi. Display. News. English.

300x250. BTF Soompi. Mobile. English.

300x250. ATF.

He was asked if he could share a spoiler for EXOs upcoming performance and he said, Its difficult for me to share details because we want the big reveal to be on the day of the closing ceremony.

But I can say that we will be singing two songs.

A lot of preparations went into it, so please anticipate our performance..

EXO has taken to the stage at many large-scale international events.

Baekhyun even sang the national anthem at the opening ceremony of the 132nd International Olympic Committee session. And now with the group set to perform at the closing ceremony of this years Winter Olympics, EXO has earned the nickname Nations Pick. Baekhyun expressed his gratitude and added, We are grateful to be given the nickname Nations Pick and we feel a greater sense of responsibility because of it. Hearing it has strengthened our resolve to keep working harder.

We believe that we were invited to perform [at the closing ceremony] because of the love and support of our fans from all over the world..

Speaking of EXOs international fans, Baekhyun was also asked if EXO knew that figure skater Evgenia Medvedeva was an EXO-L and had that she wanted to meet the group.

He replied, We would love to meet her if we get the chance, and added, Whenever we hear that an athlete is our fan, we talk about how amazing that is in our group chat.

We always have a strong desire to meet all of them..

Finally, Baekhyun concluded his interview with a message to the athletes competing in the Winter Olympics and said, I hope that everyone sees results that reflect all of the hard work they put into their training.

But I think whats most important is that they dont get injured during the competition.

I hope everyone stays injury-free and does their best till the end..

EXO and CL are set to perform at the closing ceremony of the 2018 PyeongChang Winter Olympics, which will take place on February 25.

Source () ().

For more infomation >> Baekhyun Discusses EXO's "Nation's Pick" Nickname, Upcoming Olympics Performance, And More - Duration: 4:36.

-------------------------------------------

КРУТЫЕ ТОВАРЫ С АЛИЭКСПРЕСС + КОНКУРС - Duration: 10:23.

For more infomation >> КРУТЫЕ ТОВАРЫ С АЛИЭКСПРЕСС + КОНКУРС - Duration: 10:23.

-------------------------------------------

All eyes on talks with N. Korea after PyeongChang Olympics - Duration: 12:10.

And to tell us more about what we can expect in regards to talks between the two Koreas,

as well as between the U.S. and North Korea,...

Dr. Woo Jung-yeop, a research fellow at the Sejong Institute,... joins us

in the studio today.

Welcome to the program Dr. Woo.

Good to be here.

1- So to start us off... a meeting between Ivanka Trump and Kim Yong-chol ended up

not happening.

Why so?

2- But like we heard earlier, on Sunday, Kim Yong-chol expressed an openness to talks with

the U.S.

What can we make of this?

What could be North Korea's intention behind such an offer?

3- Now the U.S. has responded cautiously to the possibility of

talks with North Korea,... saying it would first see whether Pyongyang puts de-nuclearization

on the table.

4- Let's shift our focus over a little bit to inter-Korean talks.

President Moon and Kim Yong-chol met for talks on Sunday,... just hours ahead of the closing

ceremony of the Pyeongchang Winter Olympics.

Tell us more about this unannounced meeting.

5- There are questions over what kind of "card" Kim might have brought to the meeting.

Do you think Kim Yong-chol had another message delivered to President Moon from Kim Jong-un?

6- What about the postponed joint military talks between Seoul and Washington?

7- And on Sunday, South Korea's unification ministry said that it will make efforts to

hold further talks with North Korea as the Olympics helped revive momentum for inter-Korean

dialogue.

So when can we expect the inter-Korean summit to take place?

8- Meanwhile U.S. President Donald Trump said Friday that the U.S. had leveled its (QUOTE-UNQUOTE)

"heaviest sanctions ever" against Pyongyang.

What impact would such sanctions

have on

North Korea's shipping and trading abilities.

9- The timing of this announcement of the sanctions was also

interesting considering that the U.S. has announced this right before Ivanka was to

cross paths with Kim Yong-chol at the closing ceremony

for the Olympics.

10- And if the new sanctions don't succeed in curtailing North Korea's aggression,...

Trump said a "phase two" could be the next step.

What's this "phase two," and what can we expect on this front?

11- And the Trump administration has been preparing to expand interceptions of ships

suspected of violating sanctions on North Korea.

How would South Korea go about joining this plan, and what impact would

such

actions have on inter-Korean relations?

Thank you

for your insight today.

My pleasure.

For more infomation >> All eyes on talks with N. Korea after PyeongChang Olympics - Duration: 12:10.

-------------------------------------------

1 Simple Reason To Never Use A Slider On Your Church's Website | Pro Church Daily Ep. #043 - Duration: 9:10.

For more infomation >> 1 Simple Reason To Never Use A Slider On Your Church's Website | Pro Church Daily Ep. #043 - Duration: 9:10.

-------------------------------------------

What Documents Do I Use In A Contract for Deed Deal? - Duration: 3:07.

Hey, it's Joe.

Got another question here.

This one is, "In my market I get a lot of contract for deed clients for both buyers

and sellers.

I understand that a contract for deed is similar to a land contract.

I want to know, do you have any contract for deed assignment of contracts that are available

to obtain and what two or three documents are needed to do a contract for deed assignment

to set up a deal correctly, assign our interest to the buyer?"

If you're in my mentor program, in the contract zip file you can download an example of a

land contract.

You can also get those contracts on, just by searching Google you could probably find

one that way or you could have your attorney draw one up.

Most land contracts are contract for deeds, and contract for deeds by the way is in a

trust deed state, land contracts are in mortgage states.

So if you know you've got mortgages, and you're in a land contract state, if you've

got trust deeds, then you know you're in a contract for deed state.

And you can get those, what I would suggest is, when you know you're going to do a deal

like that, you have the attorney draw one up for you, you pay them for it, you have

them send it to you on a Word document, so now you've got a copy of it that you can

modify for future use.

If you're going to assign a deal on a land contract, instead of taking a land contract

yourself, and assigning it, you're going to get a purchase agreement that allows you

to buy it on a land contract that is assignable and contingent upon approval by your investor,

which is the person you're going to sell it to.

So you get a purchase agreement, it's going to be assignable, it's going to be contingent

on approval by your investor, and you're going to be able to have ninety days to close

and then you're going to go out and find a new buyer who's going to buy it on a land

contract and then you assign your right using an assignment form which, again, you can,

you can get that online or you can get any attorney to draw it up.

Basically it just says, "I'm going to assign my right to buy to you," and of course,

if you're in the mentor program, it's in the contracts zip file.

And you can assign your right to buy to those people and then they can close the deal between

the buyer and seller, usually at a title company where they're going to get title insurance

to close that deal.

So that's the way that would work.

The other thing you might want to have is a disclosure form, and I've got those in

my documents as well.

Just make sure that the people know that they're counting on themselves to, the value and the

condition of the property and those types of things to make sure that they're not

expecting you to be their realtor.

Make sure that they're not expecting you to represent them in the deal and that they're

doing their own due diligence.

It's important to have anybody who's buying from you or selling for you to sign that document

so it doesn't make you responsible for those things.

All right, hopefully that answers the question.

Good luck with it.

For more infomation >> What Documents Do I Use In A Contract for Deed Deal? - Duration: 3:07.

-------------------------------------------

How Often Should You Change Air Filters? - Duration: 8:45.

How often should I change my air filters in my house?

That's an excellent question and we're going to talk about that today.

Hi there. I'm Angela Brown and this is Ask a House Cleaner.

This is a show where you get to ask a house cleaning question

and I get to help you find an answer.

Now today's show is brought to us by HouseCleaning360.com

which is an online referral hub of everything 360 that you need for the home.

So, if you need an HVAC guy to come out and help you

with your air conditioning and your heating, you will find them on HouseCleaning360.com

But you ask, what is HVAC?

It stands for heating, ventilation, and air conditioning, so the same person that fixes

your heating in the winter time will fix your air conditioning in the summer,

so you want to get on a maintenance plan where they come out

periodically throughout the year and they keep your systems up to par. Alright.

HouseCleaning360.com

Now onto today's show which is about how often do I change my air filters?

That's an excellent question and it comes down to all air filters are not created equal.

I'm going to show you a couple of air conditioning filters that we can take a look at today and

then you can decide which is going to be best for you and how often you're going to need

to change those based on your lifestyle.

So the very first thing that we have to look at is, what does an air filter do?

Well an air filter filters out dust, airborne pathogens, dust mites, it's going to be bacteria,

let's say that somebody in your house is coughing and sneezing,

that stuff circulates through the air.

So when the air conditioning unit or the heater kicks on and off,

air is sucked in and out of your house.

As it's sucked in and out and it circulates throughout your house, we breathe a lot of that stuff.

So in our bodies we have a built in air filter and it's our lungs and our lungs

filter in the air that we breathe through our nose and our mouth.

And so if you are constantly taking in all this gunk, then yeah your body's gets sick

and you get what we know as allergies.

So if there are known allergens in your house which are like dust, dust mites, pet dander,

things like that, then we want to filter those out.

So instead of relying on our bodies to filter all that stuff, we have the help of air filters

which filter it out in the air that we breathe inside our homes.

Alright, so let's take a look at a couple of air filters, shall we?

I have some here that I would like to share with you and the first one here is green and

it's made of a fiberglass like material and you can see through it.

It's not very thick and so this is going to be on the cheaper side and there are cheap

ones and then there are ones that are fairly expensive and I say fairly expensive for an

air filter, but what are you getting.

If you're getting better health and it's removing all that stuff from your lungs so that you

don't have to breathe that inside your body, it's well worth the price.

So instead of just going with super cheap ones,

my suggestion would be get one that's

going to do the job.

Okay, so now this one is pretty thin.

It does have a full coverage, so it is going to trap some kind of air particles and pet

dander and stuff like that, so it is good, but you'll have to change it more frequently

because it's so thin.

Alright, the next one that I have is a little bit ... and they come in all different sizes

and shapes.

This is a little bit different in that it has these like little pouches so it's going

to catch dust at a different level and then as it sucks the air in, and this is when the

air conditioning unit kicks on and off and the air goes in and out, it's going to gather

a lot of that stuff and it's going to stick to your air filter and that's why we change it.

Now on the bottom of this there's a little arrow and the arrow will show you which way

you're going to plug that into your air vent so there's a little grate, you open the grate

and you take the vent out and then you put the next vent in.

And like I say, it will show you which direction it goes, so this is a do it yourself project.

This is something you can do at home.

If you're a professional house cleaner, this might be an up sell service where you say

every three months or whatever we will change the air filters in your house and then the

customer can order them let's say for example on Amazon and just have them shipped via Prime

so they're not paying for the shipping every time, have them shipped to the house waiting

for you so you can pop in the air filters when you get to their house.

But it is ... this is a little bit thicker.

You cannot see through it.

It's made of some kind of a fiber that's heavier and it looks like it's going to do a better job.

Alright now this is like the mac daddy where it is completely covered.

I can't see through it at all.

It has multiple little ridges on it and they're much closer together, so as you have a filter

like this, everything that it catches, it's going to catch and it is not getting through here.

It's just going to absorb it right here.

It staying right here and so because this is a heavy duty one, you might not have to

replace this for several months.

Alright so the general rule of thumb is this, you should change your air filters if you

have a really good one, every three to six months and that is if you are a solo person.

You live by yourself or you have a vacation house, so you don't need to change it very

often if there are no pets, you're never at home, whatever.

There's not a whole lot of stuff happening inside the house.

Now if you're a family and you have lots of people coming and going and the doors are

opening and closing and whatever and the house is lived in frequently then you want to change

your air filters, even if they're really heavy duty, probably every three months.

That would be a really good time frame to change your filters.

Now if you throw pets into the mix, that's where it gets a little bit interesting.

If you have one pet, I would change it every two months because now you have pet dander

and you have the pet coming in and out and bringing things in on its fur that you would

not normally have if it were just people.

So if you're opening and closing doors and you have animals coming and going,

probably every two months and for every pet you have thereafter,

I would change it then every one month.

So, every 30 days if you have more than two pets because that way you're going to get

a lot more stuff in your house.

So what we're looking at preventing and taking out of the airwaves are allergens, mold, bacteria

from sickness, coughing, sneezing, dust, dust mites.

We're looking at taking all that stuff out of the air that circulates in the air that

we breathe.

If we can create a clean environment to live in and this goes along with house cleaning,

where we remove the dust and we vacuum regularly, and things like that, that is going to keep

our lungs functioning at a much higher level.

And so if your lungs are functioning, that means your eyes are clear.

That means your nose is clear and that you can breathe and breathing, according to the

American Lung Association, is the only thing that matters.

When you can't breathe nothing else matters and it's kind of a catchy slogan but it makes

a lot of sense when you think about it.

If you can't breathe you die, right?

So, keeping the air that we breathe clean is paramount.

And so how often do you clean your air filters? Regularly. Regularly.

And get the high end air filters so that you have a better chance of filtering all that

stuff out because what we're talking about is your body

and if your body is healthy then you're well.

You function better. You're able to think more clearly.

You're able to be more effective and you feel better and when you feel better you're more productive.

So, something as small as an air filter in your house can make all the difference and

so if you have pets, do it on a regular basis, every month or so.

If you don't have pets and you rarely use your house and it's a vacation home or it's

a bed and breakfast or something and it's not getting a lot of use, maybe every three

to six months.

You don't need it as often, but make sure that it's on a schedule and make it on your

calendar so that you know when you're going to change those air filters and don't go a

year in between because then that's when everything gets clogged up.

And if you've ever had a clogged drain, how the water backs up, and it's not functioning

properly, when your air filters get clogged up, it's a whole lot like that clogged drain.

The air unit doesn't work as properly.

The heating doesn't work as properly.

Nothing works as properly and then you're breathing that stuff that's not getting filtered

out through your air filters.

Alrighty, so that's my two cents for today and until we meet again,

leave the world a cleaner place then when you found it.

No comments:

Post a Comment